SNOW JADE

Technical Guides

Waterjet Mixing Tube Sizes: How to Choose Bore and Length

7 min read SNOW JADE technical team

A mixing tube looks like a simple consumable: a short, hard tube with a hole through it. In practice it is one of the two or three parts that decide what your cut looks like. Buy the wrong bore and the cut is slow or rough; buy the wrong length and it will not seat in the head.

This guide covers the three dimensions that define a mixing tube, how the size code usually works, and how to confirm a replacement without guessing.

What the mixing tube does

In an abrasive waterjet cutting head, the orifice turns high-pressure water into a fine, fast jet. That jet then passes through the mixing tube, where abrasive is drawn in and accelerated. The tube also confines the jet and gives the stream its shape before it leaves the nozzle.

Two consequences follow. First, the tube’s internal bore controls how much abrasive can pass and how tightly the stream stays together. Second, because the tube is where abrasive travels at speed, it wears — the bore grows, the inlet taper rounds off, and cut quality drifts before the part actually fails.

The three dimensions that define a tube

Every mixing tube or focusing tube is defined by three numbers:

  1. Outer diameter (OD). This is what locates the tube in the cutting head. A .281 in. tube will not fit a head machined for a .375 in. tube.
  2. Bore (inner diameter). The wear-critical dimension, and the one buyers most often get wrong.
  3. Overall length. Set by the head geometry and the standoff the head was designed for.

A part number that only tells you the bore is not enough. A part number that only tells you the length is not enough either.

Size ranges we list

The table below reflects the sizes published in the SNOW JADE 2026 catalogue. It is a description of what we stock and list, not a statement about every size any manufacturer has ever produced.

Family Outer diameter Bores listed Lengths listed
FLOW .281 in. mixing tube 0.281 in. (7.137 mm) 0.020–0.050 in. (0.508–1.27 mm) 2.00–5.00 in. (50.8–127 mm)
KMT .375 in. focusing tube 0.375 in. (9.525 mm) 0.030–0.063 in. (0.762–1.60 mm) 2.50–3.125 in. (63.5–79.4 mm)
AccuStream .300 in. nozzle 0.300 in. 0.020–0.050 in. 3.00–4.00 in.
Jet Edge .250 in. nozzle 0.250 in. 0.020–0.050 in. 3.00 in.

The same physical size can appear in more than one family. Among FLOW .281 in. tubes, for example, a .040 in. bore × 3.00 in. length is listed under several reference families: 012680-40-30, 010460-40-30, 014214-40-30 and 014194-40-30. Same bore, same length, four different references — because they belong to different catalogue families. They are not interchangeable by number, even though the dimensions match. If your parts book gives a reference, use the reference; the dimensions alone will not tell you which family your head needs. For a closer comparison of two references that describe the same tube, see Waterjet Mixing Tubes: Same Size, Different Part Numbers.

How to choose the bore

Bore selection is a trade-off between cut quality and cutting speed.

  • A smaller bore concentrates the abrasive stream. It generally produces a finer finish and a narrower kerf, and it is the usual choice when the job is finish-critical or the material is thin. It also cuts more slowly, and it is less forgiving of abrasive that is too coarse.
  • A larger bore passes more abrasive and cuts faster, at the cost of a wider kerf and a rougher edge. It is the usual choice for thicker material and for work where speed matters more than finish.

Two practical rules reduce the guesswork:

  1. Match the bore to the abrasive grit you actually run. A fine bore with coarse abrasive clogs and wears at the inlet. If you are changing grit, re-check the bore.
  2. Change one variable at a time. If you move both bore and abrasive size together, you will not know which change produced the result.

If you are unsure, the safest starting point is the size currently on the machine. Measure it, or read the marking, and replace like for like before experimenting.

How to choose the length

Length is not a tuning parameter in the same way the bore is — it is a fitment requirement. The tube has to sit in the head at the designed standoff, with the inlet positioned correctly relative to the orifice.

In practice: take the length from the parts book or from the old tube, not from a general recommendation. Lengths are listed in 0.50 in. steps in some families, which means a 3.00 in. tube and a 3.50 in. tube can look identical in a photo. This is also why a reference number sometimes covers more than one length: in our catalogue, reference 10126969 is printed against both a 3.00 in. and a 3.125 in. KMT focusing tube. When you order, state the length explicitly even if you quote a reference.

Reading the size code

Many FLOW-style references follow a readable pattern: `012680-40-30` breaks down as family, bore and length — .040 in. bore, 3.00 in. length. That pattern is a useful sanity check, not a substitute for the parts book, because other families use different digits in the same positions.

A quick method: read the last two groups as bore and length, then verify against a physical measurement. If the pattern and the measurement disagree, trust the measurement and ask before ordering.

Measuring a worn tube

You need three readings:

  1. Bore. Use a pin gauge or a bore gauge at the outlet end. A worn tube will read larger than nominal, so a used tube is a poor reference for the original size — measure near the inlet, or measure a new tube if you have one.
  2. Outer diameter. A caliper across the barrel, away from any wear marks or burrs.
  3. Length. End to end, with the tube square in the caliper jaws.

Write the three numbers down before you contact anyone. Three numbers plus a photo will identify a tube faster than five emails.

Signs the tube is due for replacement

Wear shows up in the cut before it shows up on the part:

  • the kerf widens or develops a taper that was not there before;
  • cut quality drops at the same settings and the same abrasive;
  • the outlet end of the bore looks bell-mouthed or chipped;
  • abrasive starts escaping around the nozzle instead of going through the stream;
  • the tube no longer seats cleanly, or the inlet taper is visibly rounded.

None of these tells you a service life in hours — that number depends on abrasive type, water quality, pressure settings and how the machine is run. Judge by the cut and by measurement, not by a calendar.

Ordering the right replacement

Send four things: the reference number from the parts book, the bore, the length, and the version marking on the old tube. If the marking is gone, send the three measurements and a photo.

Browse the orifices and mixing tubes category for the full size list, or start from a common size: .020 in. bore × 3.00 in., .040 in. bore × 3.00 in., .050 in. bore × 3.00 in., and the larger-diameter KMT .375 in. focusing tube, .063 in..

Request a quote

WhatsApp: +852 56170632

Email: sales@snowjadeindustrial.com

SNOW JADE is an independent supplier of aftermarket waterjet replacement parts and is not affiliated with, authorised by, or endorsed by the original equipment manufacturers. Brand names and reference numbers are used only to identify replacement applications. Dimensions and fitment are confirmed on the quotation.

Related guides

Continue Reading

Parts sourcing

Need Help Finding the Right Replacement Part?

Send us your reference part number, equipment model or product photo. SNOW JADE can help identify compatible replacement parts and coordinate sourcing through our partner suppliers in China.

Inquiry list0